1981 Mercury Lynx Review
1981 Mercury Lynx is a Wagon 4-dr style car .Made in United States, 1981 Mercury Lynx has 2 trims priced by the manufacturer at 0 with just total of 10 recalls in the past 1981 Mercury Lynx. It’s seating No data people with doors and a rank size of No data gallon. The engine is 1.6L L4 OHV 8V .
Vin Numbers
- 1MEBP6521BT629963
- 1MEBP6526BW636650
- 1MEBP6327BW656134
Safety & Recalls
Recall 81V045000 started on /Date(355377600000-0400)/.
Summary: FUEL MAY POSSIBLY TRAVEL THROUGH THE SPEED CONTROL VACUUM LINES AND INTO THE SPEED CONTROL ACTUATION DEVICE (SERV0). THE FUEL CAN DAMAGE SEALS IN THE ACTUATOR SERVO AND ALLOW VACUUM LEAKS. SUCH A LEAK COULD ACTIVATE THE SPEED CONTROL WITHOUT ANY ACTION ON THE PART OF THE DRIVER. THIS WOULD CAUSE THE VEHICLE TO GRADUALLY ACCELERATE.
Consequence: Not Defined
Remedy: THE VACUUM CHECK VALVE AND HOSE ASSEMBLY WILL BE REPLACED AND THE SPEED CONTROL SERVO WILL BE REPLACED IF IT HAS BEEN DAMAGED.
Recall 81V084000 started on /Date(363326400000-0400)/.
Summary: SOME VEHICLES EQUIPPED WITH POWER BRAKE BOOSTERS HAVE FRONT AND REAR SHELLS THAT MAY HAVE BEEN IMPROPERLY JOINED. IMPROPERLY JOINED BOOSTER SHELLS MAY SEPARATE EITHER PARTIALLY OR COMPLETELY DURING BRAKE APPLICATION.
Consequence: Not Defined
Remedy: ALL DEFECTIVE BOOSTERS WILL BE REPLACED AT NO CHARGE TO OWNER.
Recall 80V133000 started on /Date(340430400000-0400)/.
Summary: SOME OF THE INVOLVED VEHICLES WERE PRODUCED WITH AN ENGINE COMPARTMENT WIRE ASSEMBLY THAT MAY HAVE BEEN ROUTED ABOVE THE AIR CONDITIONING SUCTION HOSE. THIS HOSE MAY PUSH UP ON THE WIRING HARNESS CAUSING IT TO CONTACT THE HOOD PROP ROD BRACKET ATTACHING BOLT. THIS COULD LEAD TO PENETRATION OR CHAFING OF THE WIRING INSULATION.
Consequence: Not Defined
Remedy: DEALER WILL INSPECT AND, IF NECESSARY, CORRECT THE WIRING HARNESS ROUTING AT NO CHARGE TO OWNER.
Recall 80V134000 started on /Date(339393600000-0400)/.
Summary: ON CERTAIN VEHICLES, THE RIGHT AND LEFT HAND REAR BRAKE BACKING PLATE ATTACHMENT BOLTS MAY NOT HAVE BEEN TIGHTENED TO THE CORRECT SPECIFICATIONS. BACKING PLATE BOLTS MAY NOT BE ABLE TO WITHSTAND THE LOADS EXPERIENCED DURING TRUCK SHIPMENT. IF THE BOLTS LOOSEN FROM THE SPINDLE DURING OPERATION, BACKING PLATE MOVEMENT MAY RESULT IN WEAKENING OR PREMATURE WEAR OF ONE OR BOTH REAR BRAKE TUBES. THIS COULD LEAD TO LOSS OF BRAKE FLUID.
Consequence: Not Defined
Remedy: DEALER WILL INSPECT AND TIGHTEN THE BOLTS TO THE PROPER SPECIFICATIONS. REAR BRAKE TUBES WILL BE REPLACED, IF NECESSARY, AT NO CHARGE TO OWNER.
Recall 80V142000 started on /Date(342162000000-0500)/.
Summary: ON CERTAIN VEHICLES, METAL FASTENERS THAT WERE USED TO SECURE THE CARPETING TO THE FLOOR PAN MAY HAVE ACCIDENTALLY PENETRATED THE TOP OF THE FUEL TANK. THIS WOULD RESULT IN A SLIGHT FUEL LEAK.
Consequence: Not Defined
Remedy: DEALER WILL INSPECT VEHICLES FOR PENETRATION OF THE FUEL TANK BY CARPET FASTENERS. ANY LEAKING FUEL TANKS WILL BE REPLACED AND THE FLOOR PAN WILL BE SEALED, WITHOUT CHARGE TO OWNERS.
Recall 81V092000 started on /Date(364622400000-0400)/.
Summary: SOME OF THE INVOLVED VEHICLES HAVE AN ELECTRICALLY UNGROUNDED FUEL INLET. THESE VEHICLES ARE SUBJECT TO STATIC CHARGE ACCUMULATION AT THE FUEL FILLER PIPE OPENING, WHICH CAN OCCUR IF THESE VEHICLES ARE REFUELED FROM AN ELECTRICALLY UNGROUNDED DISPENSING NOZZLE.
Consequence: Not Defined
Remedy: A GROUNDING CONNECTION FROM THE FILLER PIPE INLET TO THE VEHICLE BODY AND A STATIC ELECTRICITY SUPPRESSION ROD INSIDE THE FILLER PIPE WILL BE INSTALLED AT NO CHARGE TO OWNER.
Recall 84V071000 started on /Date(456120000000-0400)/.
Summary: SEAT FRAME STRUCTURE COULD SEVER FRONT SEAT BELTS IF VEHICLE IS INVOLVED IN AN ACCIDENT, DEPENDING ON FORCE OF IMPACT.
Consequence: Not Defined
Remedy: DEALER WILL INSTALL A MOLDED SPACER BETWEEN REINFORCEMENT PLATES AND LOWER DECORATIVE PLASTIC COVER.
Recall 83V063000 started on /Date(425102400000-0400)/.
Summary: DOOR LOCK PILLARS COULD DEVELOP FATIGUE CRACKS FROM NORMAL USAGE OF DOOR, AT THE POINT WHERE DOOR LATCH STRIKER REINFORCEMENTS ARE ATTACHED.
Consequence: Not Defined
Remedy: ANY DAMAGED LOCK PILLARS WILL BE REPAIRED AND REINFORCEMENTS WILL BE INSTALLED BETWEEN THE DOOR LATCH STRIKER AND LOCK PILLARS.
Recall 83V013000 started on /Date(414306000000-0500)/.
Summary: THE PORTION OF THE ROOF ABOVE FRAME (RAIL) TO WHICH THE SHOULDER BELT IS ANCHORED MAY HAVE A SLOT THAT CAN COMPROMISE THE STRENGTH OF THE SHOULDER BELT ANCHOR UNDER CERTAIN SEVERE LOADS. (THE SUSPECT AREA IS NOT VISIBLE.) CONSEQUENTLY, SOME VEHICLES INCLUDED IN THIS RECALL MAY NOT MEET THE 3000 POUND ANCHORAGE STRENGTH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 210, "SEAT BELT ASSEMBLY ANCHORAGES".
Consequence: Not Defined
Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, REINFORCE THE ROOF RAIL INNER PANEL SURROUNDING THE DRAINAGE HOLE AT NO COST TO OWNER.
Recall 84V085000 started on /Date(458971200000-0400)/.
Summary: SCREW THAT CONNECTS THE SEAT BACK FRAME TO THE RECLINER MECHANISM MAY BREAK.
Consequence: Not Defined
Remedy: THE ATTACHMENT SCREW ON THE DRIVER"S SEAT WILL BE REPLACED BY ONE OF A LARGER DIAMETER.