1991 Plymouth Voyager Review

Recall 91V191000 started on /Date(688971600000-0500)/.

Summary: THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE HOSE MAY LEAK OR DETACH AT ITS CRIMPED END FITTING RESULTING IN THE DISCHARGE OF HYDRAULIC FLUID.

Consequence: FLUID DISCHARGE EVENTUALLY CAUSES THE LOSS OF BOTH THEANTI-LOCK BRAKE SYSTEM AND HYDRAULIC ASSIST FOR THE BRAKE SYSTEM, RESULTING ININCREASED LIKELIHOOD OF BRAKE LOCKUP AND INCREASED STOPPING DISTANCES, WHICHCOULD RESULT IN A VEHICLE ACCIDENT.

Remedy: REPLACE THE ABS HIGH PRESSURE HOSE WITH A HOSE OF DIFFERENT DESIGN AND CONSTRUCTION.

Recall 92V030000 started on /Date(700203600000-0500)/.

Summary: THE ANTI-LOCK BRAKE SYSTEM HIGH PRESSURE PUMP MAY BE POROUS WHICH WILL RESULT IN BRAKE FLUID LEAKAGE.

Consequence: FLUID LEAKAGE EVENTUALLY CAUSES THE LOSS OF BOTH THEANTI-LOCK BRAKE SYSTEM AND HYDRAULIC ASSIST FOR THE BRAKE SYSTEM, RESULTING ININCREASED LIKELIHOOD OF BRAKE LOCKUP AND INCREASED STOPPING DISTANCES, WHICHCOULD RESULT IN A VEHICLE ACCIDENT.

Remedy: REPLACE THE ABS HIGH PRESSURE PUMP AND HIGH PRESSURE HOSE IF THE LAST SIX DIGITS OF THE BAR CODE LABEL ON THE PUMP ARE BETWEEN 052300 AND 059262.

Recall 95I001006 started on /Date(796280400000-0500)/.

Summary: VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

Consequence: IF THE LIFTGATE LATCH OPENS, OCCUPANTS CAN BE EJECTED RESULTING IN SIGNIFICANTLY INCREASED RISK OF INJURY OR DEATH.

Remedy: CHRYSLER DEALERS WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS OF THESE VEHICLES IN MARCH 1996.

Recall 95I001002 started on /Date(796280400000-0500)/.

Summary: VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

Consequence: IF THE LIFTGATE LATCH OPENS, OCCUPANTS CAN BE EJECTED RESULTING IN SIGNIFICANTLY INCREASED RISK OF INJURY OR DEATH.

Remedy: CHRYSLER DEALERS WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS OF THESE VEHICLES IN OCTOBER 1995.

Recall 96V099000 started on /Date(834638400000-0400)/.

Summary: THE ABS HYDRAULIC CONTROL UNIT CAN EXPERIENCE EXCESSIVE BRAKE ACTUATOR PISTON SEAL WEAR CAUSING PUMP-MOTOR DETERIORATION.

Consequence: IF THIS CONDITION OCCURS, THE ABS FUNCTION COULD BE LOST AND REDUCED POWER ASSIST WOULD BE EXPERIENCED DURING VEHICLE BRAKING INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL TEST THE VEHICLE'S ANTI-LOCK BRAKE SYSTEM AND REPAIR THE VEHICLES IF NECESSARY. ALSO THE WARRANTY ON ALL ABS COMPONENTS WILL BE EXTENDED TO 10 YEARS OR 100,000 MILES (EXCEPT FOR THE BRAKE ACTUATOR PISTON ASSEMBLY AND THE PUMP-MOTOR ASSEMBLY WHICH WILL HAVE A LIFETIME COVERAGE). OWNERS WILL ALSO BE REIMBURSED FOR PREVIOUS ABS COMPONENT REPAIR COSTS.

Recall 96V229000 started on /Date(848293200000-0500)/.

Summary: THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

Consequence: IF THE STEERING WHEEL SEPARATES FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN, LOSS OF CONTROL CAN OCCUR INCREASING THE RISK OF AN ACCIDENT.

Remedy: DEALERS WILL INSPECT THE STEERING WHEEL FOR ARMATURE CRACKS IN THE CENTER HUB ATTACHMENT AREA. ANY STEERING WHEELS SHOWING CRACKS WILL BE REPLACED. ALL OTHER VEHICLES WILL HAVE A REINFORCEMENT PLATE INSTALLED TO PREVENT STEERING WHEEL SEPARATION IN THE EVENT CRACKING OCCURS.

Recall 97V148000 started on /Date(873777600000-0400)/.

Summary: VEHICLE DESCRIPTION: PASSENGER MINI-VANS. COVERS ON THE SOLID STALK MOUNTED SEAT BELT BUCKLES CAN BECOME DISLODGED CAUSING THE RELEASE BUTTON TO STICK INSIDE THE COVER. THE BUCKLE WOULD THEN BE ONLY PARTIALLY LATCHED.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED INCREASING THE RISK OF PERSONAL INJURY.

Remedy: DEALERS WILL INSTALL A COVER RETAINING CLIP TO THE STALK MOUNTED BUCKLE COVER TO PREVENT DISLOCATION OF THE BUCKLE COVER.

Recall 97V149000 started on /Date(873777600000-0400)/.

Summary: VEHICLE DESCRIPTION: PASSENGER MINI-VANS. THE CENTER REAR SEAT, RIGHT OUTBOARD SIDE, SAFETY BELT ANCHOR HOOK CAN BECOME UNATTACHED FROM THE BODY ANCHOR POSITION.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED INCREASING THE RISK OF PERSONAL INJURY.

Remedy: DEALERS WILL REPLACE THE ANCHOR HOOK RETAINING CLIP WITH A REVISED PROFILE CLIP AND A COVER PLATE.

Recall 99V189000 started on /Date(932097600000-0400)/.

Summary: VEHICLE DESCRIPTION: MINIVANS. THE LEFT HAND WINDSHIELD WIPER PIVOT DRIVE ARM WAS NOT MECHANICALLY STAKED TO THE PIVOT SHAFT.

Consequence: THIS COULD ALLOW THE DRIVE ARM TO DISENGAGE FROM THE SHAFT LEADING TO A LOSS OF WIPER FUNCTION. THE DRIVER'S VISIBILITY WOULD BE IMPAIRED, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE LEFT HAND SIDE WINDSHIELD WIPER PIVOT ASSEMBLY.

Recall 99V213000 started on /Date(936244800000-0400)/.

Summary: VEHICLE DESCRIPTION: MINI VANS. THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

Consequence: PERSONAL INJURY COULD OCCUR IF THE BOLTS BREAK ALLOWING THE LIFTGATE TO FALL SUDDENLY.

Remedy: DEALERS WILL INSPECT FOR LOOSE FASTENERS, IF THE FASTENERS ARE LOOSE, THE STRUT (AND INTEGRAL BOLTS) WILL BE REPLACED. IF THE BOLT SHOWS EVIDENCE OF TORQUE, THE BOLT WILL BE REMOVED, LARGER WASHERS WILL REPLACE THE EXISTING WASHER AND THE BOLT WILL BE REINSTALLED AND HAND TIGHTENED TO THE TARGET TORQUED.