1994 Chrysler Town & Country Review

Recall 00V305000 started on /Date(971323200000-0400)/.

Summary: VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH 2-SPOKE LUXURY WHEELS MANUFACTURED JULY 1992 THROUGH JUNE 1993; OR EQUIPPED WITH 4-SPOKE SPORT WHEELS MANUFACTURED FROM JULY 1992 THROUGH SEPTEMBER 1993. THE STEERING WHEEL ARMATURE STAMPING CAN CRACK AND SEPARATE FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN.

Consequence: IF THE STEERING WHEEL SEPARATES FROM THE CENTER HUB ATTACHMENT TO THE STEERING COLUMN, LOSS OF CONTROL CAN OCCUR INCREASING THE RISK OF AN ACCIDENT.

Remedy: DEALERS WILL INSPECT THE STEERING WHEEL FOR CRACKS AND ANY WHEELS WITH CRACKS WILL BE REPLACED. ALL OTHER VEHICLES WILL HAVE A REINFORCEMENT PLATE INSTALLED TO PREVENT STEERING WHEEL SEPARATION IN THE EVENT CRACKING OCCURS.

Recall 93V215000 started on /Date(755845200000-0500)/.

Summary: WHEELS WITH MISFORMED LUG NUT SEATS WERE INSTALLED ON THESE VEHICLES. THIS CAUSES REDUCED NUT TO WHEEL CONTACT AREA AND LIMITS THE WHEEL SELF-CENTERING CAPABILITY DURING INSTALLATION. THIS RESULTS IN LOSS OF WHEEL LUG NUT TORQUE RETENTION.

Consequence: LOSS OF LUG NUT TORQUE RETENTION MAY LEAD TO WHEEL LUGFAILURE WHICH MAY CAUSE WHEEL SEPARATION AND AN ACCIDENT.

Remedy: INSPECT THE WHEEL ASSEMBLY PLANT CODE; REPLACE WHEELS KNOWN TO HAVE THE PROBLEM AND INSTALL NEW LUG NUTS.

Recall 95I001005 started on /Date(796280400000-0500)/.

Summary: VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITH REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

Consequence: IF THE LIFTGATE LATCH OPENS, OCCUPANTS CAN BE EJECTED RESULTING IN SIGNIFICANTLY INCREASED RISK OF INJURY OR DEATH.

Remedy: CHRYSLER WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS DURING DECEMBER 1995.

Recall 95I001001 started on /Date(796280400000-0500)/.

Summary: VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER MINIVANS WITHOUT REMOTE RELEASE. THIS IS NOT A SAFETY RECALL. THERE HAS BEEN NO DETERMINATION THAT A SAFETY DEFECT EXISTS WITH THE MINIVAN LATCHES. CHRYSLER IS CONDUCTING A SERVICE CAMPAIGN TO REPLACE THE LIFTGATE LATCH ASSEMBLY OF THE AFFECTED MINIVANS. IN A COLLISION, THE REAR LIFTGATE LATCH ASSEMBLY COULD OPEN.

Consequence: IF THE LIFTGATE LATCH OPENS, OCCUPANTS CAN BE EJECTED RESULTING IN SIGNIFICANTLY INCREASED RISK OF INJURY OR DEATH.

Remedy: CHRYSLER DEALERS WILL REPLACE THE LIFTGATE LATCH WITH A NEW STRONGER LATCH ASSEMBLY WITHOUT CHARGE. CHRYSLER BEGAN NOTIFYING OWNERS OF THESE VEHICLES BEGINNING SEPTEMBER 1995.

Recall 99V113000 started on /Date(925963200000-0400)/.

Summary: VEHICLE DESCRIPTION: MINI VANS. THE WIRING THAT INITIATES THE DRIVER AND/OR PASSENGER AIR BAG COULD ELECTRICALLY SHORT CIRCUIT TO GROUND. A SHORT CIRCUIT TO GROUND THAT EXISTS IMMEDIATELY AFTER TURNING THE IGNITION KEY TO THE "ON" OR "START" POSITION CAN CAUSE THE AIR BAG(S) TO INADVERTENTLY DEPLOY.

Consequence: INADVERTENT AIR BAG DEPLOYMENT CAN INJURE A FRONT SEAT OCCUPANT.

Remedy: DEALERS WILL PERFORM AN ELECTRONIC DIAGNOSTIC CHECK. ANY SHORT CIRCUITS IDENTIFIED IN EITHER THE DRIVER'S OR PASSENGER SIDE AIR BAG INITIATOR WIRE CIRCUIT WILL BE REPAIRED.

Recall 99V213000 started on /Date(936244800000-0400)/.

Summary: VEHICLE DESCRIPTION: MINI VANS. THE BOLTS USED TO ATTACH THE STRUT TO THE BODY AND THE REAR LIFTGATE CAN ACCUMULATE FATIGUE DAMAGE IF THREE FACTORS COMBINE. IF THE BOLT IS LOOSE, THE GAS STRUT IS OVER-PRESSURIZED, AND THE FREQUENCY OF OPENING AND CLOSING CYCLES IS HIGHER THAN FOR THE AVERAGE CUSTOMER, THE BOLT CAN FAIL.

Consequence: PERSONAL INJURY COULD OCCUR IF THE BOLTS BREAK ALLOWING THE LIFTGATE TO FALL SUDDENLY.

Remedy: DEALERS WILL INSPECT FOR LOOSE FASTENERS, IF THE FASTENERS ARE LOOSE, THE STRUT (AND INTEGRAL BOLTS) WILL BE REPLACED. IF THE BOLT SHOWS EVIDENCE OF TORQUE, THE BOLT WILL BE REMOVED, LARGER WASHERS WILL REPLACE THE EXISTING WASHER AND THE BOLT WILL BE REINSTALLED AND HAND TIGHTENED TO THE TARGET TORQUED.