1996 AM General Hummer Review

Recall 06E043000 started on /Date(1148011200000-0400)/.

Summary: CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

Consequence: THIS CONDITION MAY CAUSE AN INADEQUATE SEAL AT THE CONNECTION, POTENTIALLY LEADING TO A FUEL LEAK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.

Remedy: HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).

Recall 07E088000 started on /Date(1193198400000-0400)/.

Summary: CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

Consequence: THIS CONDITION MAY CAUSE INADEQUATE SEALING AND LOSS OF ENGINE OIL, POSSIBLY RESULTING IN A FIRE.

Remedy: HONEYWELL WILL REPLACE THE AFFECTED OIL FILTERS FREE OF CHARGE. THE RECALL BEGAN DURING NOVEMBER 2007. OWNERS CAN CONTACT FRAM CUSTOMER SERVICE TOLL-FREE AT 1-800-890-2075.

Recall 96V049000 started on /Date(826606800000-0500)/.

Summary: THE COATING USED TO PROTECT THE ACCELERATOR PEDAL SHAFT IS INCOMPATIBLE WITH THE BRONZE BUSHING THROUGH WHICH THE SHAFT PASSES. OVER TIME, AND IN THE PRESENCE OF A CORROSIVE ENVIRONMENT (WATER, ROAD SALT), THE SHAFT CAN CORRODE INSIDE THE BUSHING INCREASING THE AMOUNT OF FRICTION BETWEEN THE ROTATING SHAFT AND THE STATIONARY BUSHING.

Consequence: A CORRODED ACCELERATOR PEDAL SHAFT CAN CAUSE THE ENGINE THROTTLE TO BIND AND NOT FULLY RETURN TO IDLE WHEN THE OPERATOR'S FOOT IS REMOVED FROM THE ACCELERATOR PEDAL INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSTALL A REVISED ACCELERATOR PEDAL AND SHAFT ASSEMBLY.

Recall 96V178002 started on /Date(843796800000-0400)/.

Summary: VEHICLE DESCRIPTION: BUSES EQUIPPED WITH ISRINGHAUSEN SEATS IN THE DRIVER POSITION. TWO WELDS LOCATED ON THE BACK REST ADJUSTMENT SIDE OF THE SEAT FRAME DID NOT MEET THE MANUFACTURER'S SPECIFICATIONS.

Consequence: IF THESE WELDS WERE NOT TO SPECIFICATION, BACK REST LOADS COULD CAUSE THE WELDS TO FAIL. THE BACK REST WOULD DISENGAGE FROM THE SEAT FRAME ALLOWING LOSS OF SUPPORT TO THE DRIVER'S TORSO AND POSSIBLY CAUSING LOSS OF CONTROL OF THE VEHICLE.

Remedy: ISRINGHAUSEN IS CONDUCTING THE OWNER NOTIFICATION AND REMEDY CAMPAIGN FOR THIS RECALL. DEALERS WILL INSPECT THESE SEATS AND REPLACE THE SEAT FRAME ASSEMBLY.