1988 Mazda 626 Review
1988 Mazda 626 is a Sedan 4-dr style car measuring 179.30 in length and 55.50 in height. Made in Japan, 1988 Mazda 626 has 3 trims priced by the manufacturer at 13,099 with just total of 6 recalls in the past 1988 Mazda 626. It’s seating 5 people with 4 doors and a rank size of 15.90 gallon. The engine is 2.2L L4 SOHC 12V and uses 24 of gasoline in the city and 24 on highways.
Vin Numbers
- JM1GD2423J1523406
- JM1GD2423J1587123
Safety & Recalls
Recall 88V022000 started on /Date(572504400000-0500)/.
Summary: AT AMBIENT TEMPERATURES BELOW 0 DEGREE F, FROST MAY ACCUMULATE WITHIN THE THROTTLE BODY UNDER EXTENDED CONSTANT SPEED OPERATION.
Consequence: FROST ACCUMULATION ON THE THROTTLE VALVE MAY PREVENT THEVALVE FROM RETURNING SMOOTHLY.
Remedy: INSTALL A NEW TYPE THERMOSTAT DESIGNED TO RAISE THE COOLANT TEMPERATURE AND WARM THE THROTTLE BODY TO A LEVEL ABOVE FREEZING.
Recall 87V186000 started on /Date(565851600000-0500)/.
Summary: FUEL TANK FIXING BAND RETENTION IS NOT SUFFICIENT, ALLOWING THE BAND TO RUB AGAINST THE FUEL TANK BY VEHICLE VIBRATIONS.
Consequence: THIS COULD WEAR A HOLE IN THE FUEL TANK WHICH COULDRESULT IN FUEL LEAKAGE.
Remedy: REPAIR FUEL FIXING BAND BY INSTALLING A RUBBER SHEET.
Recall 87V149000 started on /Date(558849600000-0400)/.
Summary: FLOOR MAT COULD INTERFERE WITH RELEASE OF ACCELERATOR PEDAL DUE TO IMPROPER SHAPE OF MAT.
Consequence: THIS COULD RESULT IN LOSS OF ACCELERATOR CONTROL ANDCREATE POTENTIAL FOR AN ACCIDENT.
Remedy: REMOVE PRESENT MAT AND REPLACE WITH NEW IMPROVED MAT.
Recall 88V063000 started on /Date(576993600000-0400)/.
Summary: THE DRIVE SPRING THAT DRIVES THE AUTOMATIC BELT MAY BREAK.
Consequence: THIS WOULD PREVENT FULL FORWARD MOVEMENT OF THE SEAT BELTANCHORAGE FROM THE LOCK POSITION WHEN THE DOOR IS OPENED.
Remedy: REPLACE AUTOMATIC SHOULDER BELT.
Recall 87V196000 started on /Date(567752400000-0500)/.
Summary: VEHICLES EQUIPPED WITH REAR BRAKE DRUMS TRANSPORTED BY TRAIN MAY EXPERIENCE SEPARATION OF THE BRAKE SHOE FROM THE WHEEL BRAKE CYLINDER PISTON.
Consequence: SHOULD SEPARATION OCCUR, REPEATED BRAKE OPERATION MAYDAMAGE THE WHEEL BRAKE CYLINDER DUST BOOT, ALLOWING WATER OR DUST INTRUSION ANDSUBSEQUENT PISTON CONTAMINATION.
Remedy: ALL VEHICLES WILL BE INSPECTED AND IF NO SEPARATION IS FOUND GREASE WILL BE APPLIED TO THE COMPONENT INTERFACE TO LOWER FRICTION AND AVOID SUBSEQUENT RELATIVE MOTION. IF SEPARATION IS FOUND THE WHEEL BRAKE CYLINDER DUST BOOT WILL BE REPLACED.
Recall 93V174000 started on /Date(751867200000-0400)/.
Summary: RESIN MOLDED FRONT HANDLES FAIL AT THE DOOR LATCH ACTUATING ROD ATTACHMENT, FREEING THE ROD TO FALL INSIDE THE DOOR FRAME. SUBSEQUENT LOWERING OF THE ASSOCIATED WINDOW MAY FORCE THE ACTUATING ROD DOWNWARD AND RELEASE THE DOOR LATCH.
Consequence: INADVERTENT ACTUATION OF THE DOOR LATCH CAUSES THE DOORTO OPEN UNEXPECTEDLY WHICH COULD RESULT IN AN OCCUPANT FALLING OUT OF THEVEHICLE.
Remedy: DEALERS WILL REPLACE THE DOOR HANDLE/LATCH ASSEMBLY.